Acrosser AR-ES6003FL User Manual

AR-ES6003FL User Manual 1

Item Description Quantity1 TOP COVER(Thermal Module) 1 2 B6003 1 3 BOTTOM Cover 1 4 Wall Mount Bracket 2 5 CF BRACKET 1 6 IO PANEL 1 7 Adapto

Chapter 2 Procedures of Assembly/Disassembly 2.1 SO-DIMM Installation The following instructions will guide you to install SO-DIMM step-by-step. 2

2.1.2 Open top cover. 12

2.1.3 Install the SO-DIMM memory module into the SO-DIMM socket.  Align the memory module's cutout with the SO-DIMM slot notch.  Slide the

2.2 Extension PCI/PCIe Card Installation(RS21) 2.2.1 Open the top cover (the same as above steps). 2.2.2 Unfasten the screw in order to release the

2.2.3 Push the PCI/PCIe card into PCI/PCIe slot. 15

2.2.4 Fixed the PCI/PCIe cards by PCI-E bracket.  To easily fix the PCI/PCIe cards, please make sure the card bracket aligns to the PCI-E bracket.

2.2.5 Fix the PCI/PCIe cards on chassis by fastening the screw. SCREW 17

2.3 Extension PCIe Cards Installation(RS20) In order to plug 2 PCI-E cards into system. The raiser card MUST be changed. Following introductions sho

2.3.2 Unfasten 2 screws to separate RS-21 and bracket. 19

Copyright All Rights Reserved. Manual’s first edition: For the purpose of improving reliability, design and function, the information in this docum

2.3.3 Assembly the RS20 with bracket by fastening 2 screws. 2.3.4 Install the RS20 module back to system by fastening 2 screws. 20

2.3.5 Push the PCIe cards into PCIe slot. 21

2.3.6 Fixed the PCIe cards by PCI-E bracket.  To easily fix the PCIe cards, please make sure the card bracket aligns to the PCI-E bracket. Please c

2.3.7 Fix the PCIe cards on chassis by fastening the screw. 23

2.4 2.5”HDD Installation 2.4.1 Unfasten 4 screws to release the HDD bracket. 24

2.4.2 Take out 4 HDD screws from packing bag. 2.4.3 Assemble HDD into bracket by fastening 4 screws. 25

2.4.3 Fixed HDD module back to bottom cover. 2.4.4 Plug SATA cable and power cable into M/B. 26

2.4.5 Assemble the bottom cover back to system. 27

2.5 Mounting Bracket Assembly 2.5.1 Tack out the Mounting Bracket and 4 screws from packing bag. 28

2.5.2 Fix the Mounting Brackets on system by fastening 4 screws. 29

Table of Contents Chapter 1 System Introduction ...5 1.1 Specifica

2.6 CF Card Installation 2.6.1 Unfasten the 2 screws and pull the CF bracket from I/O panel. 30

2.6.2 Assemble the CF card with CF bracket. The direction for installing the CF card 31

2.6.4 Finish the CF installation. 32

AR-B6003 Board User Manual 33

Chapter 3 Mainboard Introduction AR-B6003 is an embedded SBC that is designed for rugged environment. Without compromise the performance, it equippe

3.2 Package Contents Check if the following items are included in the package. z 　 Quick Manual z 　 AR-B6003 board z 　 1 x Software Utility CD

Chapter 4 H/W Information This chapter describes the installation of AR-B6003. At first, it shows the Function diagram and the layout of AR-B6003. It

Mainboard illustration (Bottom Side) BH1 System RTC battery socket In tel Atom Pineview D425/D525 CPU PCIE_R1 PCI-E & PCI riser card

4.2 Locations of IO ports & Jumper Setting Definition (Top Side) 38

Locations Of IO Ports & Jumper Setting Definition (Bottom Side) 39

Chapter 7 Driver And Utility Installation ...68 7.1 Driver CD Interface Introduction.

FPIO1 ATX Power on/off & Reset switch button connector. LED1 2 in 1 LED for Power & HDD LED. CF1 CF CARD SOCKET SIM1 SIM card Holder PWR

4.2.1 Connectors and Jumper settings 1. FPIO1 2. SIM1 Connector FPIO1 Connector Pin1-2 ATX Power on/off switch button Pin5-6 System Reset switch

8. COM3_COM4 ( for COM3,COM4 use ) 9. SW2 ( RS-422,RS-485 function select ) Pin SIGNAL 1 DCD 2 SIN 3 SOUT 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI SW2

12, SW5 (RS-422 RX terminator resistor selection) 13. VGA1 (D-SUB 15 pin Connector) SW5 DIP Switch For RS-422 RX Terminator resistor selection) (Defa

16. CN_RS232_1 17. CN_RS422_485_1 (For COM2 Function select). 18. LVDS1 (30 pin DF13 Connector). CN_RS232_1: For RS-232 Function CN_RS422_485_1:

19.LCDPWR1 (LCD Power Connector) 20. CN4 (ATX12V Power Input) Pin 1 VCC Pin 2 NC Pin 3 GND 21. CCMOS1. 22. SATA1, SATA2 (SATA device conn

23. SATA_PWR1, SATA_PWR2 24. FP_USB1,FP_USB2 SATA_PWR1, SATA_PWR2 SATA Device Po ector wer Conn PIN SIGNAL 1 +12V 2 GND 3 VCC3 4 VCC5 26. BH1

Chapter 5 BIOS Settings This chapter describes the BIOS menu displays and explains how to perform common tasks needed to get the system up and runnin

5.1 Main Setup Once you enter the Award BIOS™ CMOS Setup Utility, the Main Menu will appear on the screen. Use the arrow keys to highlight the item

Halt On All Errors, All but keyboard(Default)Select the situation in which you want the BIOS to stop the No Errors, POST process and notify you. Base

Chapter 1 System Introduction AR-ES6003FL is a fanless embedded system that is designed for rugged environment. Without compromise the performance,

Option Choice Description IDE HDD Auto-Detection Enter size, head…. On this channel To auto-detect the CF'sIDE Channel 0 Master Auto(Default

5.2 Advanced Chipset Setup This section consists of configuration entries that allow you improve your system performance, or modify some

Enabl fault) ed(DeEnables APIC (Advanced Programmable Interrupt Controller) functionality. APIC Mode In O ) it Display Firstnboard(DefaultPEG Auto de

5.3 PnP/PCI Setup The option configures the PCI bus system. All PCI bus system on the system use INT#, thus all installed PCI cards must be set to thi

5.4 Peripherals Setup This option controls the configuration of the board’s chipset. Control keys for this screen are the same as for the previous scr

OnboarDisabled 4F8/IRQ4E8/IRQ10(Default) Select an ad onding interrupt for eacd Serial Port 4 10 dress and the corresph serial port. USB Device Settin

Option Choice Description IDE DMA transfer access Disable Enable(Default) Enable or disable IDE DMA transfer access. SATA Mode IDE(Default) AHCI

5.5 PC Health Setup This section shows the parameters in determining the PC Health Status. These parameters include temperatures, fan speeds, and volt

5.6 Boot setup This option allows user to select sequence/priority of boot device(s) and Boot from LAN. Note: Listed at the bottom of the menu are t

Boot Other Device Disabled Enable(Default) The BIOS attempts to load the operating system from the devices in the sequence selected in these items. Ha

1.2 Packing List Check if the following items are included in the package.  AR-ES6003FL system  Quick user manual  CD with Driver and Manual  SAT

5.7 Exit Setup This option is used to exit the BIOS main menu and change password. Note: Listed at the bottom of the menu are the control keys. If y

Defaults (Y/N)? N Exit Without Saving Pressing <Enter> on this item for confirmation: Quit without saving (Y/N)? Y This allows you to exit Setu

Chapter 6 Function Description 6.1 DC Power input connection AR-B6003 needs +12V to power the board. If you use standard ATX PSU, you need to connect

6.2 Digital Inputs There are 4 clamped diode protection digital inputs on GPIO_COM1 connector. You can read the status of any input through the softwa

6.3 Digital Outputs There are 4 clamped diode protection digital outputs on GPIO_COM1 connector. You can control the output status of these digital ou

6.4 Watchdog Timer If you set a watchdog timer, you can use it to reset the system when system hangs up due to hardware issue. After you set the watch

Pin number RS-232 male 1 DCD 2 TXD 3 RXD 4 DSR 5 GND 6 DTR 7 CTS 8 RTS 9 RI CN_RS232_1: For RS-232 Function Pin SIGNAL 1 DSR 2 DCD 3 RTS 4 SIN 5

6.6 Serial ATA (SATA) There are 2 SATA 2.5 ports on the AR-B6003. There are also two SATA power connectors for the SATA hard disks. The SATA power ca

Chapter 7 Driver And Utility Installation 7.1 Driver CD Interface Introduction Acrosser provides the driver CD including the drivers, utiliti

Click the item, all the drivers will be selected. Click the item, all selected items will be cancelled. 69

1.4 System Dissection 1.4.1 Dimensions 7

Click the “Install” icon to install the selected drivers. Click the item to browse the CD contents. 70

Click the icon to close the program. 71

7.1.2 Utility Page There is one utility for AR-B6003. The detailed information please refers to Software Programming Guide for how to use the API. ¾

7.1.3 Application Page There is one application for Acrobat reader installing. ¾ Double click the “Acrobat Reader 9.2” to install the application.

7.1.4 Document Page This page will provide Acrosser board and system user manual. Please remember to install the Acrobat Reader before you read the ma

¾ Please install the Acrobat Reader when you see the message. 75

7.2 Windows XP 32bit Driver Installation 7.2.1 Please put the driver disk to optical driver. The program will appear on the screen. Please click th

7.2.2 Click the “Install” icon to install the drivers. 7.2.3 Finish the driver installation. Please click “Yes” to restart the system. 77

7.3 Windows 7 32/64bit Driver Installation 7.3.1 Please put the driver disk to optical driver. Then click the “Run setup.exe” to run the install pr

7.3.2 The program will appear on the screen. Please click the “Select All” icon. 7.3.3 Click the “Install” icon to install the drivers. 79

1.4.2 I/O Panel 8

7.3.4 Finish the driver installation. Please click “Yes” to restart the system. 80

Chapter 8 Software Installation and Programming Guide 8.1 Introduction Overview of GPIO and Watchdog AR-B6003 provides both a GPIO interface and a Wa

8.2 File Descriptions GPIO and Watchdog On Linux platform: 1. sio_acce.c The source code of the Watchdog and GPIO APIs for accessing the SuperIO. 2.

8.3 API List and Descriptions GPIO 1. Syntax: i32 getInChLevel( i32 channel, u8 *val ) Description: Get the value of GPIO Input and put the v

Parameters: I. The parameter ‘channel’ indicates the GPIO Output pins to set. Users can use the macros GPO0, GPO1, GPO2, GPO3 to indicate the GPIO O

Here is an example: If GPIO Output channel 0 and channel 2 are both 1. unsigned char ch; getOutChLevel( GPO0|GPO2, &ch ); The returned value

8.4 Enable TESTSIGNING on Windows 7 X64 system In order that the APIs works correctly on the Windows 7 X64 system, users have to enable the boot confi

3. Run the ‘bcdedit’ again without any option. A new item ‘testsigning’ is enabled. 4. Reboot the system. 87

Appendix Appendix A: BlueTooth SPEC Standard Bluetooth v2.0 + EDR class 1(100 meter) Modulation AFH (Adaptive Frequency Hopping) Profiles provi

89Appendix C: Sierra 3.5G SPEC The Sierra Wireless MC8790 PCI Express Mini Card is a compact, lightweight, wireless UMTS based modem. It provides G

1.4.3 System Configuration 12 3412 6 75817 911 13 14 18 15 10 9