Acrosser AR-B1042 User Manual

AR-B1042 PC/104 VGA/LCD DISPLAY MODULE User’ s Guide Edition: 1.42 Book Number: AR-B1042-99.B02

AR-B1042 User’s Guide 2-1 2. SETTING UP THE SYSTEM This section describes pin assignments for system’s external connectors and the jumpers setting. z

AR-B1042 User’s Guide 2-2 2.2 SYSTEM SETTING Before installing the AR-B1042 VGA module, you should first configure the VGA board’s hardware. This sec

AR-B1042 User’s Guide 2-3 2.2.1 Universal Panel Control (CON1) Attach a display panel connector to this 44-pin connector with pin assignments as show

AR-B1042 User’s Guide 2-4 2.2.4 PC/104 Connector (1) 64 Pin PC/104 Connector Bus A & B (CON5) CON53264133-IOCHCK ---SD7 ---SD6 ---SD5 ---SD4 ---S

AR-B1042 User’s Guide 2-5 (3) I/O Channel Signal Description Name Description BUSCLK [Output] The BUSCLK signal of the I/O channel is asynchronous t

AR-B1042 User’s Guide 2-6 Name Description -MASTER [Input] The MASTER is the signal from the I/O processor which gains control as the master and shou

AR-B1042 User’s Guide 2-7 2.2.8 Setting BIOS Bank (J5) 12Upper 32KBDSTN VGA LCD or TFTFactory PresetJ512Lower 32KBDual Mono VGA LCD33 Figure 2-10 J5:

AR-B1042 User’s Guide 3-1 3. CRT/LCD FLAT PANEL DISPLAY This section describes the configuration and installation procedure using LCD and CRT display.

AR-B1042 User’s Guide 3-2 3.3 LCD FLAT PANEL DISPLAY This section describes the configuration and installation procedure using LCD display. Skip this

AR-B1042 User’s Guide 3-3 3.4 INVERTER BOARD DESCRIPTION The inverter board is the one that supplies the high voltage signals to drive the LCD panel

AR-B1042 User’s Guide 4-1 4. INSTALLATION OF THE UTILITY SOFTWARE This chapter describes the installation of the utility software. The following topi

AR-B1042 User’s Guide 4-2 (4) Driver Installation – DOS Setup Step 1 : Install Windows as you normally would for a VGA display. Run Windows to make

AR-B1042 User’s Guide 4-3 4.1.3 AutoCAD R12 These drivers are designed to work with AutoCAD R12. They conform to the Autodesk Device Interface (ADI)

AR-B1042 User’s Guide 4-4 If you have previously installed a driver different from the TurboDLD driver, please note the following: After installing t

AR-B1042 User’s Guide 4-5 4.1.5 Word These drivers are designed to work with Microsoft Word Version 5.0 and 5.5. If you have already installed Word on

AR-B1042 User’s Guide 4-6 4.1.7 Windows NT These drivers are designed to work with Microsoft Windows NT 3.5x. Step 1 : Install Windows NT as you norm

AR-B1042 User’s Guide 4-7 4.3 THE CHIPSCPL UTILITY PROGRAM This utility program is designed to work with Microsoft Windows Version 3.1. 4.3.1 Install

AR-B1042 User’s Guide 0-1 Table of Contents 0. PREFACE...

AR-B1042 User’s Guide 4-8 VERSION <ALT V> displays version information about the current driver. HELP <ALT H> displays help information o

AR-B1042 User’s Guide 4-9 4.4.2 How to Use the Utility The SETCOL utility program allows you to specity the number of rows and columns on the screen.

AR-B1042 User’s Guide 5-1 5. ERROR (BEEP) CODES & INDEX 5.1 ERROR (BEEF) CODES There are three possible beep codes produced by the BIOS during POS

AR-B1042 User’s Guide 0-2 0.PREFACE 0.1 COPYRIGHT NOTICE AND DISCLAIMER January 1999 Acrosser Technology makes no representations or warranties with

AR-B1042 User’s Guide 0-3 0.6 ORGANIZATION This information for users covers the following topics (see the Table of Contents for a detailed listing):

AR-B1042 User’s Guide 1-1 1. OVERVIEW This chapter provides an overview of your system features and capabilities. The following topics are covered:

AR-B1042 User’s Guide 1-2 Model# (Hex) Color Text Display Font Size Pixel ResolutionDisplay Mode Dot Clock (MHz) Horizontal Freq. (KHz) Vertical Freq

AR-B1042 User’s Guide 1-3 1.3 AR-B1042 AND ACCESSORY LIST The AR-B1042 is a PC/104 form factor supports VGA controller for CRT or LCD display, it is v